Mill Tool Page

Introduction

This topic serves to describe the various tool pages available going through Mill and Mill Turn jobs. It is good practice to have all the tools for the job loaded into the Tool Crib at the start of the job. If you do, the tools for the job will already be in the Tool Crib, and the system will have pulled appropriate tools for each operation from the Tool Crib. From this tool page, you can either, choose a different tool from the Tool Crib, go into the Tool Crib to add tools from your Tool Library, or enter tool specific data manually into the Tool Data Section of the page.

 

This page will also assist in assigning Tool Numbers and Offsets, and Coolant options, as well as Speeds and Feeds.

 

Tool Crib - opens the Tool Crib for you to select a tool that you have already loaded for the job. Click to select a tool in the tools list, and click OK to assign the tool to the operation. (For Mill Turn jobs, view Mill Turn Tool Crib.)

 

Assign Tool Holder (Mill and Lathe Drilling) - opens the Milling Tool Holder Library to assign a tool holder to the tool. In the Tool Holder list on the right, select a tool holder/arbor, then click OK. The name of the selected tool holder appears in the Holder Label box. This holder is now the default tool holder for the tool, meaning that it is automatically assigned to the tool when you create an operation with this tool.

Tool Data

To select a tool for the feature,you can use the following option in one of two ways.

 

  • System Tool

Select this check box to allow the software to automatically select tools from the Tool Cribthat match the machining operation. In the case of end mills, you may alter the diameter and corner radius allowing the software to find the appropriate tool from the Tool Crib. In the case the appropriate tool sizes are not found, the software searches for a matching tool in the Tool Library. If a matching tool is found, it is added to the Tool Crib. If a matching tool is not found, a new tool is automatically created and added to the Tool Crib.

When this check box is cleared, you can edit all tool information directly in the dialog box. In this case, the defined tool is added to the Tool Crib.

 

Note: Although the Machining Data group remains the same regardless of the tool selected, The available Tool Data, and the Speed and Feed parameters vary depending on the type of tool selected. Click on a tool to display the Tool Data for that particular tool. Once open, click on Machining Data and Feeds and Speeds to see the corresponding variables.

Drill

ClosedCenter Drill

  • Diameter (1) - sets the diameter of the tool.

  • Small Diameter (2) - sets the small diameter of the tool.

  • Angle (3) - sets the angle of the area between the Small Diameter (2)  and the Diameter (1).

  • Point Angle (4) - sets the angle of the tip of the Center Drill.

  • Small Diameter Length - sets the length of the Small Diameter from end of Point Angle (4) to beginning of Angle (3).

  • Number of Flutes - specifies the number of cutting flutes for the tool.

  • Overall Length - set the total length of the tool. This value must be greater than the Protrusion Length.

  • Protrusion Length - sets the distance that the tool protrudes from the tool arbor when a tool holder is assigned to the tool.

 

The following items are displayed for informational purposes:

  • Tool Label - is the name of the tool.

  • Holder Label - displays the name of the associated tool holder. When blank, no tool holder is associated.

  • Tool Material - is the tool material type of the selected tool.

 

 

ClosedMachining Data

Machining Data

The Machining Data parameters change slightly depending on whether you are in a Turning job or Mill Turn job. All parameters are explained next.

 

  • Tool Number - opens the Assigned Tools dialog box for you to change the tool numbering.

  • Override Offsets

Clear the Override Offsets check box to use the tool number to set the Offset Register value.

Select the Override Offsets check box to allow for manual editing of the Offset Register value.

 

  • Height Offset - sets the Height Offset to be used in the posted program.
  • Diameter Offset - sets the Diameter Offset to used in the posted program.
  • Coolant - sets the coolant option for the operation. Select one of the following options: Off, Flood, Mist, Air, or Oil.

 

 

ClosedFeeds and Speeds

Feeds and Speeds

By default, the software automatically calculates feeds and speeds based on the values defined in the Stock Material Library.

 

  • Use System Feeds and Speeds

Select this check box to automatically calculate the feeds and speeds.

Clear this check box to type feeds and speeds values in the dialog box.

  • SFM/SMM - is the surface feet/meters per minute feedrate.
  • Plunge Feed per Tooth - sets the rate of depth per tooth. The value is linked to the Plunge Feedrate.
  • Spindle RPM - is the revolutions per minute of the spindle.
  • Plunge Feedrate - is the downward feedrate. This value is linked to the Plunge Feed per Tooth.

  • Dwell - sets the amount of seconds to Dwell.

     

Note: While editing the feeds and speeds, changing one value automatically calculates any other associated values. For example, if you modify the SFM value, the Spindle RPM, Cutting Feedrate, and Plunge Feedrate are automatically calculated.

 

 

ClosedDrill

  • Diameter (1)- sets the diameter of the tool.

  • Point Angle (2) - sets the angle of the tip of the Drill.

  • Flute Length (3) - sets the length of the flute/cutting portion of the tool.

  • Number of Flutes - specifies the number of cutting flutes for the tool.

  • Overall Length - set the total length of the tool. This value must be greater than the Protrusion Length.

  • Protrusion Length - sets the distance that the tool protrudes from the tool arbor when a tool holder is assigned to the tool.

 

The following items are displayed for informational purposes:

  • Tool Label - is the name of the tool.

  • Holder Label - displays the name of the associated tool holder. When blank, no tool holder is associated.

  • Tool Material - is the tool material type of the selected tool.

 

 

ClosedMachining Data

Machining Data

The Machining Data parameters change slightly depending on whether you are in a Turning job or Mill Turn job. All parameters are explained next.

 

  • Tool Number - opens the Assigned Tools dialog box for you to change the tool numbering.

  • Override Offsets

Clear the Override Offsets check box to use the tool number to set the Offset Register value.

Select the Override Offsets check box to allow for manual editing of the Offset Register value.

 

  • Height Offset - sets the Height Offset to be used in the posted program.
  • Diameter Offset - sets the Diameter Offset to used in the posted program.
  • Coolant - sets the coolant option for the operation. Select one of the following options: Off, Flood, Mist, Air, or Oil.

 

 

ClosedFeeds and Speeds

Feeds and Speeds

By default, the software automatically calculates feeds and speeds based on the values defined in the Stock Material Library.

 

  • Use System Feeds and Speeds

Select this check box to automatically calculate the feeds and speeds.

Clear this check box to type feeds and speeds values in the dialog box.

  • SFM/SMM - is the surface feet/meters per minute feedrate.
  • Spindle RPM - is the revolutions per minute of the spindle.
  • Feed per Minute - is the feedrate for the tap in feed per minute.
  • Feed per Revolution - is the total depth per revolution.

  • Dwell - sets the amount of seconds to Dwell.

     

Note: While editing the feeds and speeds, changing one value automatically calculates any other associated values. For example, if you modify the SFM value, the Spindle RPM, Cutting Feedrate, and Plunge Feedrate are automatically calculated.

 

 

ClosedSpiral Tap

  • Thread -  displays the thread type - size. This value is selected on the Feature page.

  • Ineffective Number of Threads (1) - sets the ineffective length for tap tools using the number of threads.

  • Flute Length (2) - sets the length of the flute/cutting portion of the tool.

  • Number of Flutes - specifies the number of cutting flutes for the tool.

  • Overall Length - set the total length of the tool. This value must be greater than the Protrusion Length.

  • Protrusion Length - sets the distance that the tool protrudes from the tool arbor when a tool holder is assigned to the tool.

  • Thread Direction - is disabled, as it is set on the feature page.

 

The following items are displayed for informational purposes:

  • Tool Label - is the name of the tool.

  • Holder Label - displays the name of the associated tool holder. When blank, no tool holder is associated.

  • Tool Material - is the tool material type of the selected tool.

 

 

ClosedMachining Data

Machining Data

The Machining Data parameters change slightly depending on whether you are in a Turning job or Mill Turn job. All parameters are explained next.

 

  • Tool Number - opens the Assigned Tools dialog box for you to change the tool numbering.

  • Override Offsets

Clear the Override Offsets check box to use the tool number to set the Offset Register value.

Select the Override Offsets check box to allow for manual editing of the Offset Register value.

 

  • Height Offset - sets the Height Offset to be used in the posted program.
  • Diameter Offset - sets the Diameter Offset to used in the posted program.
  • Coolant - sets the coolant option for the operation. Select one of the following options: Off, Flood, Mist, Air, or Oil.

 

 

ClosedFeeds and Speeds

Feeds and Speeds

By default, the software automatically calculates feeds and speeds based on the values defined in the Stock Material Library.

 

  • Use System Feeds and Speeds

Select this check box to automatically calculate the feeds and speeds.

Clear this check box to type feeds and speeds values in the dialog box.

  • SFM/SMM - is the surface feet/meters per minute feedrate.
  • Spindle RPM - is the revolutions per minute of the spindle.
  • Feed per Minute - is the feedrate for the tap in feed per minute.
  • Feed per Revolution - is the total depth per revolution.

  • Dwell - sets the amount of seconds to Dwell.

     

Note: While editing the feeds and speeds, changing one value automatically calculates any other associated values. For example, if you modify the SFM value, the Spindle RPM, Cutting Feedrate, and Plunge Feedrate are automatically calculated.

 

 

ClosedPoint Tap

  • Thread -  displays the thread type - size. This value is selected on the Feature page.

  • Ineffective Number of Threads (1) - sets the ineffective length for tap tools using the number of threads.

  • Flute Length (2) - sets the length of the flute/cutting portion of the tool.

  • Number of Flutes - specifies the number of cutting flutes for the tool.

  • Overall Length - set the total length of the tool. This value must be greater than the Protrusion Length.

  • Protrusion Length - sets the distance that the tool protrudes from the tool arbor when a tool holder is assigned to the tool.

  • Thread Direction - is disabled, as it is set on the feature page.

 

The following items are displayed for informational purposes:

  • Tool Label - is the name of the tool.

  • Holder Label - displays the name of the associated tool holder. When blank, no tool holder is associated.

  • Tool Material - is the tool material type of the selected tool.

 

 

ClosedMachining Data

Machining Data

The Machining Data parameters change slightly depending on whether you are in a Turning job or Mill Turn job. All parameters are explained next.

 

  • Tool Number - opens the Assigned Tools dialog box for you to change the tool numbering.

  • Override Offsets

Clear the Override Offsets check box to use the tool number to set the Offset Register value.

Select the Override Offsets check box to allow for manual editing of the Offset Register value.

 

  • Height Offset - sets the Height Offset to be used in the posted program.
  • Diameter Offset - sets the Diameter Offset to used in the posted program.
  • Coolant - sets the coolant option for the operation. Select one of the following options: Off, Flood, Mist, Air, or Oil.

 

 

ClosedFeeds and Speeds

Feeds and Speeds

By default, the software automatically calculates feeds and speeds based on the values defined in the Stock Material Library.

 

  • Use System Feeds and Speeds

Select this check box to automatically calculate the feeds and speeds.

Clear this check box to type feeds and speeds values in the dialog box.

  • SFM/SMM - is the surface feet/meters per minute feedrate.
  • Spindle RPM - is the revolutions per minute of the spindle.
  • Feed per Minute - is the feedrate for the tap in feed per minute.
  • Feed per Revolution - is the total depth per revolution.

  • Dwell - sets the amount of seconds to Dwell.

     

Note: While editing the feeds and speeds, changing one value automatically calculates any other associated values. For example, if you modify the SFM value, the Spindle RPM, Cutting Feedrate, and Plunge Feedrate are automatically calculated.

 

 

ClosedHand Tap

  • Thread -  displays the thread type - size. This value is selected on the Feature page.

  • Ineffective Number of Threads (1) - sets the ineffective length for tap tools using the number of threads.

  • Flute Length (2) - sets the length of the flute/cutting portion of the tool.

  • Number of Flutes - specifies the number of cutting flutes for the tool.

  • Overall Length - set the total length of the tool. This value must be greater than the Protrusion Length.

  • Protrusion Length - sets the distance that the tool protrudes from the tool arbor when a tool holder is assigned to the tool.

  • Thread Direction - is disabled, as it is set on the feature page.

 

The following items are displayed for informational purposes:

  • Tool Label - is the name of the tool.

  • Holder Label - displays the name of the associated tool holder. When blank, no tool holder is associated.

  • Tool Material - is the tool material type of the selected tool.

 

 

ClosedMachining Data

Machining Data

The Machining Data parameters change slightly depending on whether you are in a Turning job or Mill Turn job. All parameters are explained next.

 

  • Tool Number - opens the Assigned Tools dialog box for you to change the tool numbering.

  • Override Offsets

Clear the Override Offsets check box to use the tool number to set the Offset Register value.

Select the Override Offsets check box to allow for manual editing of the Offset Register value.

 

  • Height Offset - sets the Height Offset to be used in the posted program.
  • Diameter Offset - sets the Diameter Offset to used in the posted program.
  • Coolant - sets the coolant option for the operation. Select one of the following options: Off, Flood, Mist, Air, or Oil.

 

 

ClosedFeeds and Speeds

Feeds and Speeds

By default, the software automatically calculates feeds and speeds based on the values defined in the Stock Material Library.

 

  • Use System Feeds and Speeds

Select this check box to automatically calculate the feeds and speeds.

Clear this check box to type feeds and speeds values in the dialog box.

  • SFM/SMM - is the surface feet/meters per minute feedrate.
  • Spindle RPM - is the revolutions per minute of the spindle.
  • Feed per Minute - is the feedrate for the tap in feed per minute.
  • Feed per Revolution - is the total depth per revolution.

  • Dwell - sets the amount of seconds to Dwell.

     

Note: While editing the feeds and speeds, changing one value automatically calculates any other associated values. For example, if you modify the SFM value, the Spindle RPM, Cutting Feedrate, and Plunge Feedrate are automatically calculated.

 

 

ClosedRolling Tap

  • Thread -  displays the thread type - size. This value is selected on the Feature page.

  • Ineffective Number of Threads (1) - sets the ineffective length for tap tools using the number of threads.

  • Flute Length (2) - sets the length of the flute/cutting portion of the tool.

  • Number of Flutes - specifies the number of cutting flutes for the tool.

  • Overall Length - set the total length of the tool. This value must be greater than the Protrusion Length.

  • Protrusion Length - sets the distance that the tool protrudes from the tool arbor when a tool holder is assigned to the tool.

  • Thread Direction - is disabled, as it is set on the feature page.

 

The following items are displayed for informational purposes:

  • Tool Label - is the name of the tool.

  • Holder Label - displays the name of the associated tool holder. When blank, no tool holder is associated.

  • Tool Material - is the tool material type of the selected tool.

 

 

ClosedMachining Data

Machining Data

The Machining Data parameters change slightly depending on whether you are in a Turning job or Mill Turn job. All parameters are explained next.

 

  • Tool Number - opens the Assigned Tools dialog box for you to change the tool numbering.

  • Override Offsets

Clear the Override Offsets check box to use the tool number to set the Offset Register value.

Select the Override Offsets check box to allow for manual editing of the Offset Register value.

 

  • Height Offset - sets the Height Offset to be used in the posted program.
  • Diameter Offset - sets the Diameter Offset to used in the posted program.
  • Coolant - sets the coolant option for the operation. Select one of the following options: Off, Flood, Mist, Air, or Oil.

 

 

ClosedFeeds and Speeds

Feeds and Speeds

By default, the software automatically calculates feeds and speeds based on the values defined in the Stock Material Library.

 

  • Use System Feeds and Speeds

Select this check box to automatically calculate the feeds and speeds.

Clear this check box to type feeds and speeds values in the dialog box.

  • SFM/SMM - is the surface feet/meters per minute feedrate.
  • Spindle RPM - is the revolutions per minute of the spindle.
  • Feed per Minute - is the feedrate for the tap in feed per minute.
  • Feed per Revolution - is the total depth per revolution.

  • Dwell - sets the amount of seconds to Dwell.

     

Note: While editing the feeds and speeds, changing one value automatically calculates any other associated values. For example, if you modify the SFM value, the Spindle RPM, Cutting Feedrate, and Plunge Feedrate are automatically calculated.

 

 

ClosedChamfer Tool

  • Diameter (1)- sets the diameter of the tool.

  • Small Diameter (2) - sets the small diameter of the tool.

  • Angle (3) - sets the angle of the area between the Small Diameter (2)  and the Diameter (1).

  • Number of Flutes - specifies the number of cutting flutes for the tool.

  • Ineffective Length - specifies the length of extension on the small diameter that is not used for cutting.

  • Overall Length - set the total length of the tool. This value must be greater than the Protrusion Length.

  • Protrusion Length - sets the distance that the tool protrudes from the tool arbor when a tool holder is assigned to the tool.

 

The following items are displayed for informational purposes:

  • Tool Label - is the name of the tool.

  • Holder Label - displays the name of the associated tool holder. When blank, no tool holder is associated.

  • Tool Material - is the tool material type of the selected tool.

 

 

ClosedMachining Data

Machining Data

The Machining Data parameters change slightly depending on whether you are in a Turning job or Mill Turn job. All parameters are explained next.

 

  • Tool Number - opens the Assigned Tools dialog box for you to change the tool numbering.

  • Override Offsets

Clear the Override Offsets check box to use the tool number to set the Offset Register value.

Select the Override Offsets check box to allow for manual editing of the Offset Register value.

 

  • Height Offset - sets the Height Offset to be used in the posted program.
  • Diameter Offset - sets the Diameter Offset to used in the posted program.
  • Coolant - sets the coolant option for the operation. Select one of the following options: Off, Flood, Mist, Air, or Oil.

 

 

ClosedFeeds and Speeds

Feeds and Speeds

By default, the software automatically calculates feeds and speeds based on the values defined in the Stock Material Library.

 

  • Use System Feeds and Speeds

Select this check box to automatically calculate the feeds and speeds.

Clear this check box to type feeds and speeds values in the dialog box.

  • SFM/SMM - is the surface feet/meters per minute feedrate.
  • Plunge Feed per Tooth - sets the rate of depth per tooth. The value is linked to the Plunge Feedrate.
  • Spindle RPM - is the revolutions per minute of the spindle.
  • Plunge Feedrate - is the downward feedrate. This value is linked to the Plunge Feed per Tooth.

  • Dwell - sets the amount of seconds to Dwell.

     

Note: While editing the feeds and speeds, changing one value automatically calculates any other associated values. For example, if you modify the SFM value, the Spindle RPM, Cutting Feedrate, and Plunge Feedrate are automatically calculated.

 

 

ClosedCounterbore

  • Diameter (1)- sets the diameter of the tool.

  • Small Diameter (2) - sets the small diameter of the tool.

  • Flute Length (3) - sets the length of the flute/cutting portion of the tool.

  • Number of Flutes - specifies the number of cutting flutes for the tool.

  • Small Diameter Length - sets the length of the small diameter.

  • Overall Length - set the total length of the tool. This value must be greater than the Protrusion Length.

  • Protrusion Length - sets the distance that the tool protrudes from the tool arbor when a tool holder is assigned to the tool.

 

The following items are displayed for informational purposes:

  • Tool Label - is the name of the tool.

  • Holder Label - displays the name of the associated tool holder. When blank, no tool holder is associated.

  • Tool Material - is the tool material type of the selected tool.

 

 

ClosedMachining Data

Machining Data

The Machining Data parameters change slightly depending on whether you are in a Turning job or Mill Turn job. All parameters are explained next.

 

  • Tool Number - opens the Assigned Tools dialog box for you to change the tool numbering.

  • Override Offsets

Clear the Override Offsets check box to use the tool number to set the Offset Register value.

Select the Override Offsets check box to allow for manual editing of the Offset Register value.

 

  • Height Offset - sets the Height Offset to be used in the posted program.
  • Diameter Offset - sets the Diameter Offset to used in the posted program.
  • Coolant - sets the coolant option for the operation. Select one of the following options: Off, Flood, Mist, Air, or Oil.

 

 

ClosedFeeds and Speeds

Feeds and Speeds

By default, the software automatically calculates feeds and speeds based on the values defined in the Stock Material Library.

 

  • Use System Feeds and Speeds

Select this check box to automatically calculate the feeds and speeds.

Clear this check box to type feeds and speeds values in the dialog box.

  • SFM/SMM - is the surface feet/meters per minute feedrate.
  • Plunge Feed per Tooth - sets the rate of depth per tooth. The value is linked to the Plunge Feedrate.
  • Spindle RPM - is the revolutions per minute of the spindle.
  • Plunge Feedrate - is the downward feedrate. This value is linked to the Plunge Feed per Tooth.

  • Dwell - sets the amount of seconds to Dwell.

     

Note: While editing the feeds and speeds, changing one value automatically calculates any other associated values. For example, if you modify the SFM value, the Spindle RPM, Cutting Feedrate, and Plunge Feedrate are automatically calculated.

 

 

ClosedReamer

  • Diameter (1)- sets the diameter of the tool.

  • Ineffective Length (2) - sets the length of the chamfer on the tip of the tool.

  • Flute Length (3) - sets the length of the flute/cutting portion of the tool.

  • Number of Flutes - specifies the number of cutting flutes for the tool.

  • Overall Length - set the total length of the tool. This value must be greater than the Protrusion Length.

  • Protrusion Length - sets the distance that the tool protrudes from the tool arbor when a tool holder is assigned to the tool.

 

The following items are displayed for informational purposes:

  • Tool Label - is the name of the tool.

  • Holder Label - displays the name of the associated tool holder. When blank, no tool holder is associated.

  • Tool Material - is the tool material type of the selected tool.

 

 

ClosedMachining Data

Machining Data

The Machining Data parameters change slightly depending on whether you are in a Turning job or Mill Turn job. All parameters are explained next.

 

  • Tool Number - opens the Assigned Tools dialog box for you to change the tool numbering.

  • Override Offsets

Clear the Override Offsets check box to use the tool number to set the Offset Register value.

Select the Override Offsets check box to allow for manual editing of the Offset Register value.

 

  • Height Offset - sets the Height Offset to be used in the posted program.
  • Diameter Offset - sets the Diameter Offset to used in the posted program.
  • Coolant - sets the coolant option for the operation. Select one of the following options: Off, Flood, Mist, Air, or Oil.

 

 

ClosedFeeds and Speeds

Feeds and Speeds

By default, the software automatically calculates feeds and speeds based on the values defined in the Stock Material Library.

 

  • Use System Feeds and Speeds

Select this check box to automatically calculate the feeds and speeds.

Clear this check box to type feeds and speeds values in the dialog box.

  • SFM/SMM - is the surface feet/meters per minute feedrate.
  • Plunge Feed per Tooth - sets the rate of depth per tooth. The value is linked to the Plunge Feedrate.
  • Spindle RPM - is the revolutions per minute of the spindle.
  • Plunge Feedrate - is the downward feedrate. This value is linked to the Plunge Feed per Tooth.

  • Dwell - sets the amount of seconds to Dwell.

     

Note: While editing the feeds and speeds, changing one value automatically calculates any other associated values. For example, if you modify the SFM value, the Spindle RPM, Cutting Feedrate, and Plunge Feedrate are automatically calculated.

 

 

ClosedBoring

  • Diameter (1)- sets the diameter of the tool.

  • Number of Flutes - specifies the number of cutting flutes for the tool.

  • Overall Length - set the total length of the tool. This value must be greater than the Protrusion Length.

  • Protrusion Length - sets the distance that the tool protrudes from the tool arbor when a tool holder is assigned to the tool.

 

The following items are displayed for informational purposes:

  • Tool Label - is the name of the tool.

  • Holder Label - displays the name of the associated tool holder. When blank, no tool holder is associated.

  • Tool Material - is the tool material type of the selected tool.

 

 

ClosedMachining Data

Machining Data

The Machining Data parameters change slightly depending on whether you are in a Turning job or Mill Turn job. All parameters are explained next.

 

  • Tool Number - opens the Assigned Tools dialog box for you to change the tool numbering.

  • Override Offsets

Clear the Override Offsets check box to use the tool number to set the Offset Register value.

Select the Override Offsets check box to allow for manual editing of the Offset Register value.

 

  • Height Offset - sets the Height Offset to be used in the posted program.
  • Diameter Offset - sets the Diameter Offset to used in the posted program.
  • Coolant - sets the coolant option for the operation. Select one of the following options: Off, Flood, Mist, Air, or Oil.

 

 

ClosedFeeds and Speeds

Feeds and Speeds

By default, the software automatically calculates feeds and speeds based on the values defined in the Stock Material Library.

 

  • Use System Feeds and Speeds

Select this check box to automatically calculate the feeds and speeds.

Clear this check box to type feeds and speeds values in the dialog box.

  • SFM/SMM - is the surface feet/meters per minute feedrate.
  • Plunge Feed per Tooth - sets the rate of depth per tooth. The value is linked to the Plunge Feedrate.
  • Spindle RPM - is the revolutions per minute of the spindle.
  • Plunge Feedrate - is the downward feedrate. This value is linked to the Plunge Feed per Tooth.

  • Dwell - sets the amount of seconds to Dwell.

     

Note: While editing the feeds and speeds, changing one value automatically calculates any other associated values. For example, if you modify the SFM value, the Spindle RPM, Cutting Feedrate, and Plunge Feedrate are automatically calculated.

 

 

Mill

ClosedEndmill Rough

  • Diameter (1)- sets the diameter of the tool.

  • Flute Length (2) - sets the length of the flute/cutting portion of the tool. .

  • Corner Radius - sets the size of the corner radius.

  • Number of Flutes - specifies the number of cutting flutes for the tool

  • Overall Length - set the total length of the tool. This value must be greater than the Protrusion Length.

  • Protrusion Length - sets the distance that the tool protrudes from the tool arbor when a tool holder is assigned to the tool.

 

The following items are displayed for informational purposes:

  • Tool Label - is the name of the tool.

  • Holder Label - displays the name of the associated tool holder. When blank, no tool holder is associated.

  • Tool Material - is the tool material type of the selected tool.

 

 

ClosedMachining Data

Machining Data

The Machining Data parameters change slightly depending on whether you are in a Turning job or Mill Turn job. All parameters are explained next.

 

  • Tool Number - opens the Assigned Tools dialog box for you to change the tool numbering.

  • Override Offsets

Clear the Override Offsets check box to use the tool number to set the Offset Register value.

Select the Override Offsets check box to allow for manual editing of the Offset Register value.

 

  • Height Offset - sets the Height Offset to be used in the posted program.
  • Diameter Offset - sets the Diameter Offset to used in the posted program.
  • Coolant - sets the coolant option for the operation. Select one of the following options: Off, Flood, Mist, Air, or Oil.

 

 

ClosedFeeds and Speeds

Feeds and Speeds

By default, the software automatically calculates feeds and speeds based on the values defined in the Stock Material Library.

 

  • Use System Feeds and Speeds

Select this check box to automatically calculate the feeds and speeds.

Clear this check box to type feeds and speeds values in the dialog box.

  • SFM/SMM - is the surface feet/meters per minute feedrate.
  • Feed per Tooth - is the feedrate for feed moves in units per tooth.
  • Plunge Feed per Tooth - is the feedrate for plunge moves in units per tooth.
  • Spindle RPM - is the revolutions per minute of the spindle.
  • Cutting Feedrate - is the feedrate for feed moves.
  • Plunge Feedrate - is the feedrate for plunge moves.
  • Arc Slowdown % - is the amount of the feedrate to use when in arc moves. 100% is equal to the Cutting Feedrate.

  • Dwell - sets the amount of seconds to Dwell.

     

Note: While editing the feeds and speeds, changing one value automatically calculates any other associated values. For example, if you modify the SFM value, the Spindle RPM, Cutting Feedrate, and Plunge Feedrate are automatically calculated.

 

 

ClosedEndmill Finish

  • Diameter (1)- sets the diameter of the tool.

  • Flute Length (2) - sets the length of the flute/cutting portion of the tool. .

  • Corner Radius - sets the size of the corner radius.

  • Number of Flutes - specifies the number of cutting flutes for the tool

  • Overall Length - set the total length of the tool. This value must be greater than the Protrusion Length.

  • Protrusion Length - sets the distance that the tool protrudes from the tool arbor when a tool holder is assigned to the tool.

 

The following items are displayed for informational purposes:

  • Tool Label - is the name of the tool.

  • Holder Label - displays the name of the associated tool holder. When blank, no tool holder is associated.

  • Tool Material - is the tool material type of the selected tool.

 

 

ClosedMachining Data

Machining Data

The Machining Data parameters change slightly depending on whether you are in a Turning job or Mill Turn job. All parameters are explained next.

 

  • Tool Number - opens the Assigned Tools dialog box for you to change the tool numbering.

  • Override Offsets

Clear the Override Offsets check box to use the tool number to set the Offset Register value.

Select the Override Offsets check box to allow for manual editing of the Offset Register value.

 

  • Height Offset - sets the Height Offset to be used in the posted program.
  • Diameter Offset - sets the Diameter Offset to used in the posted program.
  • Coolant - sets the coolant option for the operation. Select one of the following options: Off, Flood, Mist, Air, or Oil.

 

 

ClosedFeeds and Speeds

Feeds and Speeds

By default, the software automatically calculates feeds and speeds based on the values defined in the Stock Material Library.

 

  • Use System Feeds and Speeds

Select this check box to automatically calculate the feeds and speeds.

Clear this check box to type feeds and speeds values in the dialog box.

  • SFM/SMM - is the surface feet/meters per minute feedrate.
  • Feed per Tooth - is the feedrate for feed moves in units per tooth.
  • Plunge Feed per Tooth - is the feedrate for plunge moves in units per tooth.
  • Spindle RPM - is the revolutions per minute of the spindle.
  • Cutting Feedrate - is the feedrate for feed moves.
  • Plunge Feedrate - is the feedrate for plunge moves.
  • Arc Slowdown % - is the amount of the feedrate to use when in arc moves. 100% is equal to the Cutting Feedrate.

  • Dwell - sets the amount of seconds to Dwell.

     

Note: While editing the feeds and speeds, changing one value automatically calculates any other associated values. For example, if you modify the SFM value, the Spindle RPM, Cutting Feedrate, and Plunge Feedrate are automatically calculated.

 

 

ClosedChamfer Mill

  • Diameter (1)- sets the diameter of the tool.

  • Angle (2) - sets the included angle of the tool.

  • Small Diameter (3) - sets the small diameter of the tool.

  • Number of Flutes - specifies the number of cutting flutes for the tool.

  • Overall Length - set the total length of the tool. This value must be greater than the Protrusion Length.

  • Protrusion Length - sets the distance that the tool protrudes from the tool arbor when a tool holder is assigned to the tool.

 

The following items are displayed for informational purposes:

  • Tool Label - is the name of the tool.

  • Holder Label - displays the name of the associated tool holder. When blank, no tool holder is associated.

  • Tool Material - is the tool material type of the selected tool.

 

 

ClosedMachining Data

Machining Data

The Machining Data parameters change slightly depending on whether you are in a Turning job or Mill Turn job. All parameters are explained next.

 

  • Tool Number - opens the Assigned Tools dialog box for you to change the tool numbering.

  • Override Offsets

Clear the Override Offsets check box to use the tool number to set the Offset Register value.

Select the Override Offsets check box to allow for manual editing of the Offset Register value.

 

  • Height Offset - sets the Height Offset to be used in the posted program.
  • Diameter Offset - sets the Diameter Offset to used in the posted program.
  • Coolant - sets the coolant option for the operation. Select one of the following options: Off, Flood, Mist, Air, or Oil.

 

 

ClosedFeeds and Speeds

Feeds and Speeds

By default, the software automatically calculates feeds and speeds based on the values defined in the Stock Material Library.

 

  • Use System Feeds and Speeds

Select this check box to automatically calculate the feeds and speeds.

Clear this check box to type feeds and speeds values in the dialog box.

  • SFM/SMM - is the surface feet/meters per minute feedrate.
  • Feed per Tooth - is the feedrate for feed moves in units per tooth.
  • Plunge Feed per Tooth - is the feedrate for plunge moves in units per tooth.
  • Spindle RPM - is the revolutions per minute of the spindle.
  • Cutting Feedrate - is the feedrate for feed moves.
  • Plunge Feedrate - is the feedrate for plunge moves.
  • Arc Slowdown % - is the amount of the feedrate to use when in arc moves. 100% is equal to the Cutting Feedrate.

  • Dwell - sets the amount of seconds to Dwell.

     

Note: While editing the feeds and speeds, changing one value automatically calculates any other associated values. For example, if you modify the SFM value, the Spindle RPM, Cutting Feedrate, and Plunge Feedrate are automatically calculated.

 

 

ClosedCorner-Round

  • Diameter (1)- sets the diameter of the tool.

  • Small Diameter (2) - sets the small diameter of the tool.

  • Corner Radius (3) - sets the corner radius size of the tool.

  • Small Diameter Length (4) - sets the size of the small diameter of the tool.

  • Shaft Diameter (5) - sets the diameter of the shaft.

  • Number of Flutes - specifies the number of cutting flutes for the tool.

  • Overall Length - set the total length of the tool. This value must be greater than the Protrusion Length.

  • Protrusion Length - sets the distance that the tool protrudes from the tool arbor when a tool holder is assigned to the tool.

 

The following items are displayed for informational purposes:

  • Tool Label - is the name of the tool.

  • Holder Label - displays the name of the associated tool holder. When blank, no tool holder is associated.

  • Tool Material - is the tool material type of the selected tool.

 

 

ClosedMachining Data

Machining Data

The Machining Data parameters change slightly depending on whether you are in a Turning job or Mill Turn job. All parameters are explained next.

 

  • Tool Number - opens the Assigned Tools dialog box for you to change the tool numbering.

  • Override Offsets

Clear the Override Offsets check box to use the tool number to set the Offset Register value.

Select the Override Offsets check box to allow for manual editing of the Offset Register value.

 

  • Height Offset - sets the Height Offset to be used in the posted program.
  • Diameter Offset - sets the Diameter Offset to used in the posted program.
  • Coolant - sets the coolant option for the operation. Select one of the following options: Off, Flood, Mist, Air, or Oil.

 

 

ClosedFeeds and Speeds

Feeds and Speeds

By default, the software automatically calculates feeds and speeds based on the values defined in the Stock Material Library.

 

  • Use System Feeds and Speeds

Select this check box to automatically calculate the feeds and speeds.

Clear this check box to type feeds and speeds values in the dialog box.

  • SFM/SMM - is the surface feet/meters per minute feedrate.
  • Feed per Tooth - is the feedrate for feed moves in units per tooth.
  • Plunge Feed per Tooth - is the feedrate for plunge moves in units per tooth.
  • Spindle RPM - is the revolutions per minute of the spindle.
  • Cutting Feedrate - is the feedrate for feed moves.
  • Plunge Feedrate - is the feedrate for plunge moves.
  • Arc Slowdown % - is the amount of the feedrate to use when in arc moves. 100% is equal to the Cutting Feedrate.

  • Dwell - sets the amount of seconds to Dwell.

     

Note: While editing the feeds and speeds, changing one value automatically calculates any other associated values. For example, if you modify the SFM value, the Spindle RPM, Cutting Feedrate, and Plunge Feedrate are automatically calculated.

 

 

ClosedThread Mill

  • Diameter (1)- sets the diameter of the tool.

  • Flute Length - sets the cutting length of the tool.

  • Overall Length - set the total length of the tool. This value must be greater than the Protrusion Length.

  • Number of Flutes - specifies the number of cutting flutes for the tool.

  • Protrusion Length (2) - sets the distance that the tool protrudes from the tool arbor when a tool holder is assigned to the tool.

  • Taper Angle (3) - sets the angle of the tool if applicable.

  • Pitch - sets the pitch of the tool.

  • Thread Height (4) - sets the height of the threads of the tool.

  • Thread Angle (5) - sets the corner radius size of the tool.

 

The following items are displayed for informational purposes:

  • Tool Label - is the name of the tool.

  • Holder Label - displays the name of the associated tool holder. When blank, no tool holder is associated.

  • Tool Material - is the tool material type of the selected tool.

 

 

ClosedMachining Data

Machining Data

The Machining Data parameters change slightly depending on whether you are in a Turning job or Mill Turn job. All parameters are explained next.

 

  • Tool Number - opens the Assigned Tools dialog box for you to change the tool numbering.

  • Override Offsets

Clear the Override Offsets check box to use the tool number to set the Offset Register value.

Select the Override Offsets check box to allow for manual editing of the Offset Register value.

 

  • Height Offset - sets the Height Offset to be used in the posted program.
  • Diameter Offset - sets the Diameter Offset to used in the posted program.
  • Coolant - sets the coolant option for the operation. Select one of the following options: Off, Flood, Mist, Air, or Oil.

 

 

ClosedFeeds and Speeds

Feeds and Speeds

By default, the software automatically calculates feeds and speeds based on the values defined in the Stock Material Library.

 

  • Use System Feeds and Speeds

Select this check box to automatically calculate the feeds and speeds.

Clear this check box to type feeds and speeds values in the dialog box.

  • SFM/SMM - is the surface feet/meters per minute feedrate.
  • Feed per Tooth - is the feedrate for feed moves in units per tooth.
  • Plunge Feed per Tooth - is the feedrate for plunge moves in units per tooth.
  • Spindle RPM - is the revolutions per minute of the spindle.
  • Cutting Feedrate - is the feedrate for feed moves.
  • Plunge Feedrate - is the feedrate for plunge moves.
  • Arc Slowdown % - is the amount of the feedrate to use when in arc moves. 100% is equal to the Cutting Feedrate.

  • Dwell - sets the amount of seconds to Dwell.

     

Note: While editing the feeds and speeds, changing one value automatically calculates any other associated values. For example, if you modify the SFM value, the Spindle RPM, Cutting Feedrate, and Plunge Feedrate are automatically calculated.

 

 

ClosedSingle Point Thread

  • Thread Type - With the system tool check box cleared, clicking Thread Type will allow you to select the Thread Type and Thread Size.

  • Diameter (1)- sets the diameter of the tool.

  • Number of Flutes - specifies the number of cutting flutes for the tool.

  • Protrusion Length (2) - sets the distance that the tool protrudes from the tool arbor when a tool holder is assigned to the tool.

  • Pitch - sets the pitch of the tool.

  • Thread Height (3) - sets the height of the threads of the tool.

  • Thread Angle (4) - sets the angle of the thread.

 

The following items are displayed for informational purposes:

  • Tool Label - is the name of the tool.

  • Holder Label - displays the name of the associated tool holder. When blank, no tool holder is associated.

  • Tool Material - is the tool material type of the selected tool.

 

 

ClosedMachining Data

Machining Data

The Machining Data parameters change slightly depending on whether you are in a Turning job or Mill Turn job. All parameters are explained next.

 

  • Tool Number - opens the Assigned Tools dialog box for you to change the tool numbering.

  • Override Offsets

Clear the Override Offsets check box to use the tool number to set the Offset Register value.

Select the Override Offsets check box to allow for manual editing of the Offset Register value.

 

  • Height Offset - sets the Height Offset to be used in the posted program.
  • Diameter Offset - sets the Diameter Offset to used in the posted program.
  • Coolant - sets the coolant option for the operation. Select one of the following options: Off, Flood, Mist, Air, or Oil.

 

 

ClosedFeeds and Speeds

Feeds and Speeds

By default, the software automatically calculates feeds and speeds based on the values defined in the Stock Material Library.

 

  • Use System Feeds and Speeds

Select this check box to automatically calculate the feeds and speeds.

Clear this check box to type feeds and speeds values in the dialog box.

  • SFM/SMM - is the surface feet/meters per minute feedrate.
  • Feed per Tooth - is the feedrate for feed moves in units per tooth.
  • Plunge Feed per Tooth - is the feedrate for plunge moves in units per tooth.
  • Spindle RPM - is the revolutions per minute of the spindle.
  • Cutting Feedrate - is the feedrate for feed moves.
  • Plunge Feedrate - is the feedrate for plunge moves.
  • Arc Slowdown % - is the amount of the feedrate to use when in arc moves. 100% is equal to the Cutting Feedrate.

  • Dwell - sets the amount of seconds to Dwell.

     

Note: While editing the feeds and speeds, changing one value automatically calculates any other associated values. For example, if you modify the SFM value, the Spindle RPM, Cutting Feedrate, and Plunge Feedrate are automatically calculated.

 

 

ClosedV-Tool

  • Diameter (1)- sets the diameter of the tool.

  • Included Angle (2) - sets the angle of the tool tip.

  • Flute Length (3) - sets the length of the flute/cutting portion of the tool.

  • Number of Flutes - specifies the number of cutting flutes for the tool.

  • Overall Length - set the total length of the tool. This value must be greater than the Protrusion Length.

  • Protrusion Length - sets the distance that the tool protrudes from the tool arbor when a tool holder is assigned to the tool.

 

The following items are displayed for informational purposes:

  • Tool Label - is the name of the tool.

  • Holder Label - displays the name of the associated tool holder. When blank, no tool holder is associated.

  • Tool Material - is the tool material type of the selected tool.

 

 

ClosedMachining Data

Machining Data

The Machining Data parameters change slightly depending on whether you are in a Turning job or Mill Turn job. All parameters are explained next.

 

  • Tool Number - opens the Assigned Tools dialog box for you to change the tool numbering.

  • Override Offsets

Clear the Override Offsets check box to use the tool number to set the Offset Register value.

Select the Override Offsets check box to allow for manual editing of the Offset Register value.

 

  • Height Offset - sets the Height Offset to be used in the posted program.
  • Diameter Offset - sets the Diameter Offset to used in the posted program.
  • Coolant - sets the coolant option for the operation. Select one of the following options: Off, Flood, Mist, Air, or Oil.

 

 

ClosedFeeds and Speeds

Feeds and Speeds

By default, the software automatically calculates feeds and speeds based on the values defined in the Stock Material Library.

 

  • Use System Feeds and Speeds

Select this check box to automatically calculate the feeds and speeds.

Clear this check box to type feeds and speeds values in the dialog box.

  • SFM/SMM - is the surface feet/meters per minute feedrate.
  • Feed per Tooth - is the feedrate for feed moves in units per tooth.
  • Plunge Feed per Tooth - is the feedrate for plunge moves in units per tooth.
  • Spindle RPM - is the revolutions per minute of the spindle.
  • Cutting Feedrate - is the feedrate for feed moves.
  • Plunge Feedrate - is the feedrate for plunge moves.
  • Arc Slowdown % - is the amount of the feedrate to use when in arc moves. 100% is equal to the Cutting Feedrate.

  • Dwell - sets the amount of seconds to Dwell.

     

Note: While editing the feeds and speeds, changing one value automatically calculates any other associated values. For example, if you modify the SFM value, the Spindle RPM, Cutting Feedrate, and Plunge Feedrate are automatically calculated.

 

 

ClosedTapered

  • Diameter (1)- sets the diameter of the tool.

  • Flute Length (2) - sets the cutting length.

  • Angle (3) - sets the angle of the taper.

  • Corner Radius - sets the corner radius of the tool.  

  • Number of Flutes - specifies the number of cutting flutes for the tool.

  • Overall Length - sets the overall length of the tool.

  • Protrusion Length (2) - sets the distance that the tool protrudes from the tool arbor when a tool holder is assigned to the tool.

 

The following items are displayed for informational purposes:

  • Tool Label - is the name of the tool.

  • Holder Label - displays the name of the associated tool holder. When blank, no tool holder is associated.

  • Tool Material - is the tool material type of the selected tool.

 

 

ClosedMachining Data

Machining Data

The Machining Data parameters change slightly depending on whether you are in a Turning job or Mill Turn job. All parameters are explained next.

 

  • Tool Number - opens the Assigned Tools dialog box for you to change the tool numbering.

  • Override Offsets

Clear the Override Offsets check box to use the tool number to set the Offset Register value.

Select the Override Offsets check box to allow for manual editing of the Offset Register value.

 

  • Height Offset - sets the Height Offset to be used in the posted program.
  • Diameter Offset - sets the Diameter Offset to used in the posted program.
  • Coolant - sets the coolant option for the operation. Select one of the following options: Off, Flood, Mist, Air, or Oil.

 

 

ClosedFeeds and Speeds

Feeds and Speeds

By default, the software automatically calculates feeds and speeds based on the values defined in the Stock Material Library.

 

  • Use System Feeds and Speeds

Select this check box to automatically calculate the feeds and speeds.

Clear this check box to type feeds and speeds values in the dialog box.

  • SFM/SMM - is the surface feet/meters per minute feedrate.
  • Feed per Tooth - is the feedrate for feed moves in units per tooth.
  • Plunge Feed per Tooth - is the feedrate for plunge moves in units per tooth.
  • Spindle RPM - is the revolutions per minute of the spindle.
  • Cutting Feedrate - is the feedrate for feed moves.
  • Plunge Feedrate - is the feedrate for plunge moves.
  • Arc Slowdown % - is the amount of the feedrate to use when in arc moves. 100% is equal to the Cutting Feedrate.

  • Dwell - sets the amount of seconds to Dwell.

     

Note: While editing the feeds and speeds, changing one value automatically calculates any other associated values. For example, if you modify the SFM value, the Spindle RPM, Cutting Feedrate, and Plunge Feedrate are automatically calculated.

 

 

ClosedT-Cutter

  • Diameter (1)- sets the diameter of the tool.

  • Flute Length (2) - sets the cutting length.

  • Corner Radius - sets the corner radius of the tool.

  • Shaft Diameter (3) -sets the diameter of the shaft.  

  • Number of Flutes - specifies the number of cutting flutes for the tool.

  • Overall Length - sets the overall length of the tool.

  • Protrusion Length  - sets the distance that the tool protrudes from the tool arbor when a tool holder is assigned to the tool.

 

The following items are displayed for informational purposes:

  • Tool Label - is the name of the tool.

  • Holder Label - displays the name of the associated tool holder. When blank, no tool holder is associated.

  • Tool Material - is the tool material type of the selected tool.

 

 

ClosedMachining Data

Machining Data

The Machining Data parameters change slightly depending on whether you are in a Turning job or Mill Turn job. All parameters are explained next.

 

  • Tool Number - opens the Assigned Tools dialog box for you to change the tool numbering.

  • Override Offsets

Clear the Override Offsets check box to use the tool number to set the Offset Register value.

Select the Override Offsets check box to allow for manual editing of the Offset Register value.

 

  • Height Offset - sets the Height Offset to be used in the posted program.
  • Diameter Offset - sets the Diameter Offset to used in the posted program.
  • Coolant - sets the coolant option for the operation. Select one of the following options: Off, Flood, Mist, Air, or Oil.

 

 

ClosedFeeds and Speeds

Feeds and Speeds

By default, the software automatically calculates feeds and speeds based on the values defined in the Stock Material Library.

 

  • Use System Feeds and Speeds

Select this check box to automatically calculate the feeds and speeds.

Clear this check box to type feeds and speeds values in the dialog box.

  • SFM/SMM - is the surface feet/meters per minute feedrate.
  • Feed per Tooth - is the feedrate for feed moves in units per tooth.
  • Plunge Feed per Tooth - is the feedrate for plunge moves in units per tooth.
  • Spindle RPM - is the revolutions per minute of the spindle.
  • Cutting Feedrate - is the feedrate for feed moves.
  • Plunge Feedrate - is the feedrate for plunge moves.
  • Arc Slowdown % - is the amount of the feedrate to use when in arc moves. 100% is equal to the Cutting Feedrate.

  • Dwell - sets the amount of seconds to Dwell.

     

Note: While editing the feeds and speeds, changing one value automatically calculates any other associated values. For example, if you modify the SFM value, the Spindle RPM, Cutting Feedrate, and Plunge Feedrate are automatically calculated.

 

 

ClosedDove Mill

  • Diameter (1)- sets the diameter of the tool.

  • Flute Length (2) - sets the cutting length.

  • Angle (3) - sets the angle of the taper.

  • Corner Radius - sets the corner radius of the tool.  

  • Number of Flutes - specifies the number of cutting flutes for the tool.

  • Overall Length - sets the overall length of the tool.

  • Protrusion Length (2) - sets the distance that the tool protrudes from the tool arbor when a tool holder is assigned to the tool.

 

The following items are displayed for informational purposes:

  • Tool Label - is the name of the tool.

  • Holder Label - displays the name of the associated tool holder. When blank, no tool holder is associated.

  • Tool Material - is the tool material type of the selected tool.

 

 

ClosedMachining Data

Machining Data

The Machining Data parameters change slightly depending on whether you are in a Turning job or Mill Turn job. All parameters are explained next.

 

  • Tool Number - opens the Assigned Tools dialog box for you to change the tool numbering.

  • Override Offsets

Clear the Override Offsets check box to use the tool number to set the Offset Register value.

Select the Override Offsets check box to allow for manual editing of the Offset Register value.

 

  • Height Offset - sets the Height Offset to be used in the posted program.
  • Diameter Offset - sets the Diameter Offset to used in the posted program.
  • Coolant - sets the coolant option for the operation. Select one of the following options: Off, Flood, Mist, Air, or Oil.

 

 

ClosedFeeds and Speeds

Feeds and Speeds

By default, the software automatically calculates feeds and speeds based on the values defined in the Stock Material Library.

 

  • Use System Feeds and Speeds

Select this check box to automatically calculate the feeds and speeds.

Clear this check box to type feeds and speeds values in the dialog box.

  • SFM/SMM - is the surface feet/meters per minute feedrate.
  • Feed per Tooth - is the feedrate for feed moves in units per tooth.
  • Plunge Feed per Tooth - is the feedrate for plunge moves in units per tooth.
  • Spindle RPM - is the revolutions per minute of the spindle.
  • Cutting Feedrate - is the feedrate for feed moves.
  • Plunge Feedrate - is the feedrate for plunge moves.
  • Arc Slowdown % - is the amount of the feedrate to use when in arc moves. 100% is equal to the Cutting Feedrate.

  • Dwell - sets the amount of seconds to Dwell.

     

Note: While editing the feeds and speeds, changing one value automatically calculates any other associated values. For example, if you modify the SFM value, the Spindle RPM, Cutting Feedrate, and Plunge Feedrate are automatically calculated.

 

 

ClosedLollipop

  • Diameter (1)- sets the diameter of the tool.

  • Flute Length (2) - sets the cutting length.

  • Shaft Diameter (3) - sets the diameter of the shaft.

  • Number of Flutes - specifies the number of cutting flutes for the tool.

  • Overall Length - sets the overall length of the tool.

  • Protrusion Length (2) - sets the distance that the tool protrudes from the tool arbor when a tool holder is assigned to the tool.

 

The following items are displayed for informational purposes:

  • Tool Label - is the name of the tool.

  • Holder Label - displays the name of the associated tool holder. When blank, no tool holder is associated.

  • Tool Material - is the tool material type of the selected tool.

 

 

ClosedMachining Data

Machining Data

The Machining Data parameters change slightly depending on whether you are in a Turning job or Mill Turn job. All parameters are explained next.

 

  • Tool Number - opens the Assigned Tools dialog box for you to change the tool numbering.

  • Override Offsets

Clear the Override Offsets check box to use the tool number to set the Offset Register value.

Select the Override Offsets check box to allow for manual editing of the Offset Register value.

 

  • Height Offset - sets the Height Offset to be used in the posted program.
  • Diameter Offset - sets the Diameter Offset to used in the posted program.
  • Coolant - sets the coolant option for the operation. Select one of the following options: Off, Flood, Mist, Air, or Oil.

 

 

ClosedFeeds and Speeds

Feeds and Speeds

By default, the software automatically calculates feeds and speeds based on the values defined in the Stock Material Library.

 

  • Use System Feeds and Speeds

Select this check box to automatically calculate the feeds and speeds.

Clear this check box to type feeds and speeds values in the dialog box.

  • SFM/SMM - is the surface feet/meters per minute feedrate.
  • Feed per Tooth - is the feedrate for feed moves in units per tooth.
  • Plunge Feed per Tooth - is the feedrate for plunge moves in units per tooth.
  • Spindle RPM - is the revolutions per minute of the spindle.
  • Cutting Feedrate - is the feedrate for feed moves.
  • Plunge Feedrate - is the feedrate for plunge moves.
  • Arc Slowdown % - is the amount of the feedrate to use when in arc moves. 100% is equal to the Cutting Feedrate.

  • Dwell - sets the amount of seconds to Dwell.

     

Note: While editing the feeds and speeds, changing one value automatically calculates any other associated values. For example, if you modify the SFM value, the Spindle RPM, Cutting Feedrate, and Plunge Feedrate are automatically calculated.

 

 

 

ClosedDrag Knife

  • Blade Thickness (1)- sets the width of the blade.

  • Blade Offset(2) - sets the distance between the tools center of rotation and the tip of the blade.

  • Protrusion Length (2) - sets the distance that the tool protrudes from the tool arbor when a tool holder is assigned to the tool.

 

The following items are displayed for informational purposes:

  • Tool Label - is the name of the tool.

  • Holder Label - displays the name of the associated tool holder. When blank, no tool holder is associated.

 

 

 

ClosedMachining Data

Machining Data

The Machining Data parameters change slightly depending on whether you are in a Turning job or Mill Turn job. All parameters are explained next.

 

  • Tool Number - opens the Assigned Tools dialog box for you to change the tool numbering.

  • Override Offsets

Clear the Override Offsets check box to use the tool number to set the Offset Register value.

Select the Override Offsets check box to allow for manual editing of the Offset Register value.

 

  • Height Offset - sets the Height Offset to be used in the posted program.
  • Diameter Offset - sets the Diameter Offset to used in the posted program.
  • Coolant - sets the coolant option for the operation. Select one of the following options: Off, Flood, Mist, Air, or Oil.

 

 

ClosedFeeds and Speeds

Feeds and Speeds

 

  • Cutting Feedrate - is the feedrate for feed moves.
  • Plunge Feedrate - is the feedrate for plunge moves.
  • Arc Slowdown % - is the amount of the feedrate to use when in arc moves. 100% is equal to the Cutting Feedrate.

Next Topic

Once the Tool variables have been set, clicking will take you to the next page of the given operation. To move the appropriate next topic, click the type of feature that has been chosen below and then the link for the desired operation.

 

ClosedHole Wizards

 

Center Drill Parameters

Drill Operation Parameters

Chamfer Drill Parameters

Chamfer Mill Patterns

Ream Parameters

Bore Parameters

Rolling Tap Parameters

Counterbore Drill Parameters

Counterbore Mill Parameters

Tap Parameters

Rolling Tap Parameters

 

Closed2 Axis Feature

 

Profile Rough Patterns

Profile Finish Patterns

Pocket Patterns

Facing Patterns

Engrave Parameters

Chamfer Mill Patterns

Plunge Rough (2 Axis) Patterns

Corner Rounding Patterns

 

Closed3 Axis Feature

 

Closed3 Axis Standard

 

Z Level Rough Patterns

Z Level Finish Patterns

Planar Patterns

Spiral Patterns

Radial Patterns

Plunge Rough Patterns

 

Closed3 Axis Pro

 

Advanced Rough Patterns

Flatlands Parameters

Equidistant Patterns

Pencil Parameters

Advanced Planar Patterns

Project Curves Patterns

Advanced Z Level Finish Patterns

 

Closed4 Axis Rotary

 

4 Axis Rotary Patterns

 

ClosedMill Thread

 

Mill Thread Pattern

 

Closed3 Axis Wireframe

 

3 Axis Wireframe Parameters

 

ClosedV-Carve

 

Tapered Pocketing Parameters

V-Varve Finishing Parameters